04/2024
Service Analyzer v92.0 is Bobcat equipment Diagnostic and Programming Dealer software that allows communication with the Electronic Control Modules (ECMs) to diagnose existing and potential problems.
1. New Small Articulated Loader (SAL) main
controller software (V1.05)
a. Support for service clock and service
clock log.
b. Adjustment to the sensor supply out of
range faults.
c. Updated hydraulic oil temperature warning and
extremely high setpoints (High: 195°F [91°C],
Extremely High: 210°F [99°C]).
d. Auxiliary pot out of neutral fault will clear on
next attempt to activate auxiliary if pot is within
the neutral range.
e. Extend and Retract out of neutral fault will clear
on the next attempt to activate extend or retract if
pot is within the neutral range.
f. Armrest faults require a key cycle to clear.
g. Support for software version log.
h. Support for engine hour meter rollover. Hour meter
will roll over to 0 when 9999.9 is reached.
i. Updates to service analyzer diagnostic screens
and fault code descriptions.
2. Fixed issue where some ECU map files were not properly
linked causing the following error to appear on
Service Analyzer “No application file available for Engine
Control Unit (ECU)”
***********************************************
Service Analyze V88.12 – 13 July 2020
1. New M-Series Loader Gateway Software (V15.04)
a. Support added for India T4 engine. LCD
will display ‘EGR’ for certain EGR faults.
– S590H*D*B: B4RF11001+
2. New R-Series Loader Cab Software (V1.06)
a. Improved bucket shake on manual machines.
***********************************************
Service Analyzer V88.11 – 2 July 2020
1. Increases coil current for Soil Asphalt
Spreader.
2. Corrected depth check errors for the
following excavator models:
D42*J**R: B4YF00001+
E42*J**R: B4GM00001+
3. New AWS Loader Drive+ software (V12.3)
a. Support for new steering solenoids
4. Updated Engine (ECU) Software for
DL01, DL02, DL03 Bobcat Engines
a. Fuel Injector valve cleaning logic
added to ECU map files for original
piston and pre-TMAP sensor equipped
original Bobcat Engines.
5. Updated the following Bobcat Engine,
V2 ECU map files:
a. Fixed issue with EGR / TVA H-Bridge
open load fault codes not clearing
after repair.
– Loader
DM02_LEL00_A06_V721
DM02_LEL01_A02_V721
DM02_LEL02_A03_V721
DM02_LEL06_A05_V721
DM02_LEL07_A02_V721
DM02_LEL08_A02_V721
DM02_MFL01_A03_V721
DM02_MFL02_A04_V721
DM02_MFL03_A02_V721
DM02_MFL04_A02_V721
DM02_MFL08_A04_V721
– Excavator
DM01_LEE00_A05_V721_ECU
DM01_LEE01_A05_V721_ECU
DM02_LEE01_A02_V721_ECU
– Telehandler
DM03_LEV00_A02_V721_ECU
DM03_MFV01_A02_V721_ECU
6. Adjusted starter engine speed cut off
level from 1000 RPM to 850 RPM on the
following machines:
– S450L*DEA: B4J711001+
– S450H*D*C: B4RH11001+
– T450L*DEA: B4J611001+
– T450H*D*B: B4RG11001+
– S510L*DEA: B4JB11001+
– S510H*D*B: B4RE11001+
– S530L*DEA: B4KA11001+
– S550L*DEA: B4ZD11001+
– S590L*DEA: B4ZE11001+
– S590H*D*B: B4RF11001+
– T590L*DEA: B4KV11001+
– T550H*D*A: B57T11001+
– T595H*D*A: B57U11001+
7. New Gauge panel software (V3.05)
a. Support for Telehandler Bobcat Engine V2
8. New R-Series Loader Hub Software (V1.13)
a. Support added for Bobcat Engine V2
with DPF.
9. New R-Series Touch Display Software
(Application: V2.5.0; Content: V1.5.0)
a. Support added for Bobcat Engine V2
with DPF.
b. Fixed issue where fuel usage statistics
was showing incorrect data.
10. New R-Series Standard Display Software
(Application V1.12.0)
a. Support added for Bobcat Engine V2
with DPF.
b. Support for software update log added.
c. Support for service code event log
added.
d. Support grading interface on grader and
box blades.
***********************************************
Service Analyzer V88.10 – 12 June 2020
1. Updates the following MEX to have
percentage based aux on the Deluxe
Display Panel:
– E26*K**R: B4S911001+
2. Fixed issue with reverse fan not working
on the following machine.
– S450D*DEA: AV9V12409+
– S450D*DAA: B1E617350+
3. R-Series Loader Hub software update (V1.12)
a. Support added for rear auxiliaries.
b. Support added for road light kit.
c. Removed Ride Control and Dual Direction
Bucket Positioning mutual exclusion.
d. Updated fan tables for 6x and 7x to reduce
power consumption.
4. Support added for R-Series Rear Auxiliary
controller (P/N: 7319142; V1.04)
5. Support added for R-Series Loader Road Lights
controller (P/N: 7319144; V1.02)
6. New R-Series Loader Touch Display software (V2.04; V1.05)
a. Support added for Laser Box Blade.
b. Fixed issue on grader screen where metric units
are not being displayed correctly.
c. Fixed issue where ECU derate would still appear on
the machine performance screen and reduced performance
icon would remain on gauge screen even after fault cleared.
d. Fixed issue preventing user data from being reset.
7. New Loader R-Series Mid Controller (V1.05)
a. Added support for neutral light kit.
8. Restore V923 (B4Z811001+) settings
***********************************************
Service Analyzer V88.09 – 20 May 2020
1. New Telehandler Software
Gateway (V6.70), Drive (V6.80), Workgroup
(V6.80)
a. Support for new Stage 5 74HP engines.
– TL30.60: B4ZJ11001+, B4ZP11001+
– TL26.60: B4ZN11001+, B4ZR11001+
– V519: B4ZS11001+
– TL30.70: B4ZT11001+, B4ZU11001+
– T35.105: B4ZV11001+
– T35.105L: B51111001+
– T36.120SL: B51211001+
– T35.130S: B51311001+
– T35.130SLP: B51411001+
– T35.140S: B51511001+
– T41.140SLP: B51611001+
– T40.180SLP: B51711001+
2. Add support for Small Articulated Loader
diagnostic screens.
***********************************************
Service Analyzer V88.08 – 11 May 2020
1. New M-Series Loader Deluxe Display
Software (V7.8)
a. Fixes issue with Laser/3D Box Blade
screen not showing.
b. Updated fault code descriptions for
Stage V engines.
2. New Compact Excavator Deluxe Display
Software (V2.9)
a. Support added for adjusting the bucket
orientation on Depth Check
b. Fixed issues with non-Latin characters
not appearing correctly
3. Added ECU map (A02_V721) support for
the following machines:
– T550H*D*A: B57T11001+
– T595H*D*A: B57U11001+
4. New R-Series Loader Hub software (V1.11)
a. Fixes issue with side lights not turning
on.
5. Added support for pressure washer attachments
– PW250M: B59100101+
– PW250L: B59200101+
***********************************************
Service Analyzer V88.07 – 29 Apr 2020
1. New R-Series Loader Hub Software (V1.9)
a. Fix issue where 000000-00 engine
faults were being logged on engine
fault history.
b. Update to fuel level tables (requires
display update).
c. Fix to hydraulic filter to prevent
plugged fault from occurring during
crank.
d. Fix issue where two speed not allowed
notification was appearing on single
speed machines.
e. Fix to auto crank feature, was disabled.
Pushing the START button for one second will
enable auto crank where machine will
crank until engine starts or 30 second
timer ends.
f. Support for grader for Touch Display
(requires Touch Display update).
g. Park Brake engagement modification.
h. Support for new joysticks.
2. Update sensor supply fault range to
4.75 for the low end and 5.25 for the high
end on all R-Series Loader controllers.
3. New R-Series Loader Standard Panel (V1.10.3)
a. Fixed issue where master password would
be off by one digit.
b. Enable reverse camera override screen
(when machine is moving in reverse) only
if camera is connected or required.
c. Fixes issue where language was not being
saved per operator.
d. Updated default service interval length
to 750 hours.
e. Update to fuel level tables (Requires
Hub controller update).
f. Updated fault code descriptions.
g. Fixed issue where units were not displayed
correctly on boot.
i. Fixed auto brightness where the label was
inverted
j. Fixed issue that could cause the panel
to turn on after a key off if auto brightness
was enabled.
k. Improved camera detection as well as fixed
issue where camera not connected fault was
occuring when a camera was never connected.
l. Fixed auto idle not saving through key cycle.
4. New R-Series Loader Touch Display Software
(Application: V2.3.1; Content: V1.3.2)
a. Support grading interface (Requires
Hub controller update).
b. Improvements when reconnecting Bluetooth
devices.
c. Update to fuel level tables (Requires
Hub controller update).
d. Fixes issue of nuisance U1185-00 (Radio No
Communication) when on the lock screen for more
than 10 seconds.
5. New Small Articulated Loader (SAL) software
(V1.4)
a. Allow starter to operate if battery voltage
is less than 6 volts.
b. Support for diagnostic screens.
6. Updated ECU map (A05_V721) for the
following machines:
– S66H***A: B4SA11001+
– S76H***A: B4CD11001+
– T66H***A: B4SB11001+
– T76H***A: B4CE11001+
7. Updated ECU map (A03_V721) for the
following machines:
– S450L*DEA: B4J711001+
– S510L*DEA: B4JB11001+
– S530L*DEA: B4KA11001+
8. Added ECU map (A01_V721) support for
the following machines:
– E50ZL*ER: B4HT11001+
– E55ZL*ER: B4HU11001+
– E60*J**R: B4GR11001+
– S450H*D*C: B4RH11001+
– T450H*D*B: B4RG11001+
– S510H*D*B: B4RE11001+
– S550L*DEA: B4ZD11001+
– S590L*DEA: B4ZE11001+
– T590L*DEA: B4KV11001+
– T450L*DEA: B4J611001+
9. Added ECU map (A02_V721) support for
the following machines:
– S590H*D*B: B4RF11001+
– S580L**EA: B51U11001+
– S76L**EA: B4ZY11001+
– T66L**EA: B51V11001+
– T76L**EA: B4ZZ11001+
10. Telehandler update, restore initial delay after power
quicktach unlock as in Service Analyzer 86.14
for following machines:
– T35105: from B3GN11001 to B3GN13999,
B3GU11001+
– T35105L: from B3GP11001 to B3GP13999,
B3GV11001+
– T36120SL: from B3GS11001 to B3GS13999,
from B3GT11001 to B3GT13999,
B3GW11001+
– T35130S: from B3KS11001 to B3KS13999,
B3KV11001+
– T35130SL: from B3KT11001 to B3KT13999,
B3KW11001+
– T35140S: from B3KU11001 to B3KU13999,
B3KY11001+
– T40140: from B1CT11001 to B1CT13999,
B33H11001+
– T40180: from B33G11001 to B33G13999,
from B33W11001 to B33W13999,
B33J11001+
***********************************************
Service Analyzer V88.05 – 17 Mar 2020
1. Support for H1 hydrostatic pump on the
following loaders:
– S510H*D*A: B42S12400+
2. Electronic Auto Shift option added for
the following machines:
– E17ZK**M: B4PT11001+
3. Updated ECU map (A04_V721) for the
following machines :
a. S62H***A: B4SE11001+
b. S64H***A: B4SC11001+
c. S66H***A: B4SA11001+
d. T62H***A: B4SF11001+
e. T64H***A: B4SD11001+
f. T66H***A: B4SB11001+
***********************************************
Service Analyzer V88.04 – 28 Feb 2020
1. Update to display P-Codes on
standard panel for the following
machines:
– S450L*DEA: B4J711001+
– S450H*D*C: B4RH11001+
– S450H*D*A: B4ZD11001+
– S510L*DEA: B4JB11001+
– S510H*D*B: B4RE11001+
– S530L*DEA: B4KA11001+
– S550M*DCA: B4U811001+
– S570M*DCA: B4U911001+
– S590H*D*B: B4RF11001+
– T450L*DEA: B4J611001+
– T450H*D*B: B4RG11001+
– T450H*D*A: B4ZE11001+
– T570L*DEA: B4KV11001+
2. Changed timeout of R-Series loader Hydraulic
Main Filter Not Connected (C1091-95) from 30
seconds to 10 minutes.
***********************************************
Service Analyzer V88.03 – 21 Feb 2020
1. Support added for Advanced Selectable Auxiliary
Control (A-SAC) on the following machines:
– E26*K*ER: B4B811001+
– E27*K*AR: B4R811001+
– E27*K*ER: B4BA11001+
– E27ZK**R: B4R711001+
– E27ZK*ER: B4B911001+
– D27ZK*ER: B4BB11001+
– E34*K*ER: B3Y311001+
– E35ZK**R: B4S511001+
– E35ZK*ER: B3Y411001+
– E37*E**R: B4S611001+
– D35ZK*ER: B4CS11001+
2. New R-Series Loader Drive Software (V1.4)
a. Fixes issue that caused swash plate
not in neutral fault before flagging
in calibration fault preventing drive
calibration from happening.
***********************************************
Service Analyzer V88.02 – 29 Jan 2020
1. New M-Series Deluxe Panel Software (V7.7)
a. Updated translations ot support Bobcat
Engine V2.
***********************************************
Service Analyzer V88.01 – 23 Jan 2020
1. Support for the following Compact Excavators
– D42*J**R: B4YF11001+
– D50*J**R: B4YG11001+
2. New software for Touch Display on compact
excavtors to fix issue where “Software
Update Needed” messages appears.
***********************************************
Service Analyzer V88.00 – 17 Jan 2020
1. R-Series Loader Software changes
a. Changed fault timing for fuel level
sensor out of range faults (P0460-16 &
P0460-17) to reduce nuisance errors
during engine crank cycle.
b. Changed fault timing for Hydraulic Main
Filter Pressure Switch – Not Connected
(C1091-95) to reduce nuisance errors.
2. New M-Series Loader gateway software (V15.3).
Fixes issue created with Service Analyzer
V87.20 that caused M-Series loaders that
are COLD to derate immediately once engine
is started causing machine to stall out.
3. Fixes issue created with Service Analyzer
V87.20 that caused H9202 (Fuel Lift Pump
Output Error On) and H9322 (Fuel Pressure
Sensor Out of Range Low) on S450H*D*A
(Serial Number: AUVB14001+).
4. New Touch Display software for Compact
Excavators (V1.7.2, V1.2.2, V2.2.1).
– Updates to translations for fault codes
and in application.
5. Support added for Small Articulated Loader (SAL)
gateway software (V1.3)
– L23*K***A – B4LC11001+
– L28*K***A – B4LD11001+
6. New M-Series Loader Deluxe Display software
(V7.6)
a. Support for Bobcat Engine V2
b. Added support for the following languages:
– Croatian
– Czech
– Danish
– Estonian
– Finnish
– Hungarian
– Latvian
– Norwegian
– Portuguese
– Romanian
– Serbian
– Slovak
– Slovenian
– Swedish
– Turkish
Type: Diagnostic and Programming Software
Languages: English, French, German, Dutch, Italian, Spanish, Czech, Chinese. – Croatian – Czech – Danish – Estonian – Finnish – Hungarian – Latvian – Norwegian – Portuguese – Romanian – Serbian – Slovak – Slovenian – Swedish
OS: Windows 10, 8.1, 8, 7 64-bit (x64) & 32-bit (x86)
Date of update: 04/2024
Bobcat Service Analyzer v92 [2024] Diagnosis Software
- International DLB [2022] Diagnosis Software
- MTU DiaSys PRO v2.73 Diagnosis Software
- Perkins Pandaros Packager -Diagnosis Software
- Bobcat Service Library Online Service & Repair Manuals
- BOBCAT EPC [2025] Online Parts Catalog
- Bendix ACom Pro [2024] Diagnostics Software
- JPRO Noregon Commercial Fleet 2024 v2 Diagnostic Software
- KOHLER KIRA 2.6 [2024] Diagnostic Software
- International Navistar NED Engine Diagnostics…